ihelp for the LuxuryTon electric scooter
Front wheel and brake installation:
First, remove the nut off the axel and put the wheel on (make sure the breaks are loose)
The last step is to thighen the nut back on the axle
Finally, screw the fenders on
Last step is to put the cover of the recliner system on and put the little screws back
Storage box installation
Take out the base of the storage box and install it on the back of the seat and then proceed to install the storage box on the base.
The front frame can be attached to the scooter with these two screws.
Before we install the windshield onto the frame, we have to put the rubber washers into the holes of the windshield. We need to put the 4 round pieces on the frame to support the windshield. After that, we tighten the windshield by these two screws and washers like you see in the pictures
First, we insert these special nuts then attach the back part of the roof to the frame. It’s the same process with the small cover as well.
To install the roof we have to put the special washers, then roof can be installed onto the frame.
If the camera does not turn on, you have to check these wires as maybe they are disconnected.
( shows a speaker attached to the port)
To adjust the brake, you need to tighten the nut on the end of the brake cable.
Fenders installation;
Put the fender in the correct position (make sure the fender holes are even with the scooter’s holes and the circle snap in to the wheel nut) but first connect the lights with the connectors.
Seatbelt installation
Open the seatbelt kit. The seatbelt has to be placed between the seat and the recliner system as shown in the picture below.
Use the big screws for the seatbelt with the recliner.
Handle bar installation
Open the small front cover of the scooter
Place the handle bar in the right position. Make sure the holes are aligned with holes of the scooter, use the big screw and nut to secure the handle bar to the scooter
Last step is to put back the small cover and screw it onto scooter with the little screws.
IF YOUR SCOOTER CAME WITH THE ROOF/WINDSHIELD, PLEASE SEE INFORMATION BELOW:
The rear frame of the roof must be attached to the scooter with the four long screws.
We have to select the right screws and install the cover like we see on the pictures
This is the roof and windshield installed:
Reverse camera installation (if applicable)
The camera has to be installed in the correct position.
The scooter must be turned ON then push the bottom R and the camera turns on automatically.
USB port information (if applicable)
The USB port works only when both the switch on the steering column and the braker unbderneath the seat are ON
ihelp for the LuxuryTon electric scooter
Front wheel and brake installation:
First, remove the nut off the axel and put the wheel on (make sure the breaks are loose)
The last step is to thighen the nut back on the axle
Finally, screw the fenders on
Last step is to put the cover of the recliner system on and put the little screws back
Storage box installation
Take out the base of the storage box and install it on the back of the seat and then proceed to install the storage box on the base.
The front frame can be attached to the scooter with these two screws.
Before we install the windshield onto the frame, we have to put the rubber washers into the holes of the windshield. We need to put the 4 round pieces on the frame to support the windshield. After that, we tighten the windshield by these two screws and washers like you see in the pictures
First, we insert these special nuts then attach the back part of the roof to the frame. It’s the same process with the small cover as well.
To install the roof we have to put the special washers, then roof can be installed onto the frame.
If the camera does not turn on, you have to check these wires as maybe they are disconnected.
( shows a speaker attached to the port)
To adjust the brake, you need to tighten the nut on the end of the brake cable.
Fenders installation;
Put the fender in the correct position (make sure the fender holes are even with the scooter’s holes and the circle snap in to the wheel nut) but first connect the lights with the connectors.
Seatbelt installation
Open the seatbelt kit. The seatbelt has to be placed between the seat and the recliner system as shown in the picture below.
Use the big screws for the seatbelt with the recliner.
Handle bar installation
Open the small front cover of the scooter
Place the handle bar in the right position. Make sure the holes are aligned with holes of the scooter, use the big screw and nut to secure the handle bar to the scooter
Last step is to put back the small cover and screw it onto scooter with the little screws.
IF YOUR SCOOTER CAME WITH THE ROOF/WINDSHIELD, PLEASE SEE INFORMATION BELOW:
The rear frame of the roof must be attached to the scooter with the four long screws.
We have to select the right screws and install the cover like we see on the pictures
This is the roof and windshield installed:
Reverse camera installation (if applicable)
The camera has to be installed in the correct position.
The scooter must be turned ON then push the bottom R and the camera turns on automatically.
USB port information (if applicable)
The USB port works only when both the switch on the steering column and the braker unbderneath the seat are ON